CCTV Hanging Hardware

12' Xtender Pole™, Telescoping Extension Pole for Hanging Hardware The 12' Xtender Pole™, Telescoping Extension Pole allows professional contractors to safely install ceiling hardware from the ground level. Working from the floor provides a safer way to reach areas that previously were dangerous or inaccessible by ladders, scaffolding, and scissorlifts. This telescoping extension pole easily reaches vaulted ceilings, over stairwells, and through ceiling grids. This multi-purpose extension pole...

18' Xtender Pole™, Telescoping Extension Pole for Hanging Hardware The 18' Xtender Pole™, Telescoping Extension Pole allows professional contractors to safely install ceiling hardware from the ground level. Working from the floor provides a safer way to reach areas that previously were dangerous or inaccessible by ladders, scaffolding, and scissorlifts. This telescoping extension pole easily reaches vaulted ceilings, over stairwells, and through ceiling grids. This multi-purpose extension pole...

1/2" Magnetic Clamp, Black The 1/2" Magnetic Clamp utilizes triple plated nickel and copper magnet and premium quality plastic to support up to 26 pounds. Installs quickly, safely, and easily without drilling necessary. It is re-usable and plenum rated. Can install on wide variety of metallic surfaces.

1/4-20 Female Magnet Screw Mount This Female Magnet Screw Mount is a magnetic mounting unit for attaching magnetic J-Hooks and bridle rings without drilling. These units are safe and easy to install quickly.

3" Eye Lag Screw, 1/4" Hole for Wood Applications This is a 3" long Eye Lag Screw with an 1/4" Eye Hole. Intended for wood installation of J-Hooks, hanging ceiling wire & jack chain, threaded rod or s-hooks. Our hardware is designed for the most efficient, secure and cost effective solution. These eye lag screws are intended for drilling into wooden surfaces. These Self-Tap Eye Lag Screws are easily installed by using the 12" or 18" Xtender Pole and Eye Lag Driver Adapter also available from...

Magnetic Cable Tie Mounts The Magnetic Cable Tie Mount is designed for harsh environmental conditions. Installs quickly, easily, and safety to be used multiple times if necessary. No drilling or soldering required for installation. Manufactured of triple plated nickel and copper, this magnetic cable tie mount can rotate 360 degrees.

Magnetic Hook and Loop Holder The Magnetic Hook and Loop Holder is designed to handle harsh conditions. It can sustain weight up to 26 pounds and can adhere to metallic surfaces many times. A 3/4" slot accommodates hook and loop cable ties for heavy duty cable support. The Magnetic Hook and Loop Holder can rotate up to 360 degrees and installs safely without drilling necessary.

Mini Magnetic Cable Tie Mount The Mini Magnetic Cable Tie Mount is designed for harsh environmental conditions. Installs quickly, easily, and safely. They are also able to be used multiple times if necessary. It has a maximum strength of 9 pounds and can rotate 360 degrees.

2" Self-Tapping Eye Lag Screw for Sheet Metal Installation of J-Hooks This is a 2" Eye Lag Screw with an 1/4" Eye Hole and 3/4" Threaded length. Intended for sheet-metal installation of J-Hooks, hanging ceiling wire & jack chain, threaded rod or s-hooks. Our hardware is designed for the most efficient, secure and cost effective solution. These Self-Tap Eye Lag Screws are easily installed by using the 12" or 18" Xtender Pole and Eye Lag Driver Adapter also available from Primus Cable. We've got...

All Purpose Clip for 1/8" - 1/2" Flanges - Box of 100 Accommodates beam flange from 1/8" to 1/2" thickness, standard 1/4-20 or #10-24 threaded bridle rings, standard drive rings as well as unthreaded rings. This clip supports both drive rings and bridle rings. Easily installs, requires on a hammer.

Beam Clamp for 1/8" - 1/2" Flanges - Box of 100 Hang ceiling wire & jack chain, threaded rod and eye lag screws with this beam clamp. Our hardware is designed for the most efficient, secure and cost effective hanging hardware solutions. These beam clamps easily install to beam flanges measuring up to 1/2." Supports 1/4" and 3/8" threaded rod.

Corrosion-Resistant Galvanized Steel 1/2", 5/8", 7/8", & 1-1/4" Drive Rings for Walls, Studs, & Rafters: These new drive rings offer the fast, easy way to run electrical, SE, SEU and communications wire or cable on interior wood framing members or exterior walls. They are made of corrosion-resistant galvanized steel. The DR series drive rings provides sturdy support for wire and cable. They are available in four sizes (measured inside the loop) and they support a range of cable bundle sizes....

Galvanized Braided Support Wire Arlington Braided Support Wire is galvanized and braided to insure that you get a quality hold. It is supplied in 500 ft rolls of ether 0.062” (1/8") or 0.08" (5/64") OD wire. Wire holds angular/static load up to 50 lbs. for the 0.062" (1/8") OD wire and 75 lbs. for the 0.08" (5/64") OD Wire. It is ideal for wet or dry locations and includes a UL listed rating.

Magnetic Cable Holders The Black Magnetic Cable Holder saves both time and money as a cable management solution. Installs quickly and easily without drilling, utilizing the power of rare earth magnets. This magnetic cable holder is triple plated with nickel, copper, and nickel and coated with premium durable plastic. This product is re-usable and helps you save time on cable management installations. Where to use Magnetic Cable Holders: Steel Beams Purlins Ceiling Decks Drop Ceiling Channels...

Magnetic Cable Holders, Pipe These Magnetic Cable Holders are ideal for running wires along metal pipes and beams. Mag Daddy's Cable Holders save on both time and money as a cable management solution. Installs quickly and easily without drilling, utilizing the power of rare earth magnets. This magnetic cable holder can hold up to 16 lbs. and rotate 360° making it simple to customize you runs. This product is re-usable and extremely easy to use. So make running cable easier by harnessing the...

180° Vertical Overhang Hanger with 1/4" Hole The 180° Vertical Overhang Hanger is ideal for hanging ceiling wire and jack chains. It works well with threaded rods, eye lag screws, our line of J-Hooks and other cable management solutions. Use for overhead routing and management of CAT5, CAT6 or Fiber Optic cable.

2" Bridle Ring for Beam Clamp, 1/4x20 Thread Support and secure your communication and other low voltage cables with this 2" diameter bridle ring. Simple, effective and constructed of solid, low carbon steel. Excellent for use with our Beam Clamps to help manage cables. The perfect choice for cable management made easy!

45° Angled Overhang Hanger with 1/4" Hole The 45° Angled Overhang Hanger is ideal for suspending ceiling wire and jack chains. Keep your electrical wires and networking cables secure with our Angled Overhang Hanger. It not only makes your networking installation safer, but also keeps cables organized and tidy for maintenance technicians. The threaded and non-threaded holes accommodate threaded rods and eye lag screws. This angled overhang hanger works well with our line of J-Hooks and other...

Z-Angle Clip w/ Powder Actuated Nail This 'Z'-Angle Clip with Powder Actuated Nail & 1/4-20 Threaded Hole for your threaded rod and J-Hook Installation. Great for overhead Cable Management of CAT5, CAT6 or Fiber Optic Cable. Mount the angle clip and add your threaded rod and j-hook attachments for a simple and easy solution to your cable routing problems. Powder Actuated Nail allows attachment of threaded rod and j-hooks into concrete with this Threaded Rod 'Z' Angle Clip. ...

Angle Clip Right w/ Powder Actuated Nail This Right Angle Clip has a 1/4" Hole for hanging j-hooks, s-hooks, jack chain or wire for the purpose of suspending CAT5, CAT6 or Fiber Optic cable. The Angle Clip is installed with a Powder Actuated Nail for use in concrete for your J-Hook applications.

Right Angle 1/4-20 Threaded Rod Clip w/ 1/4" Hole The Right Angle Threaded Rod Clip has a 1/4" Hole for overhead cable management of CAT5, CAT6 or Fiber Optic Cable. It is designed to provide the most cost effective, efficient, and secure cable management solution.

Right Angle Clip for 1/4-20 Threaded Rod, Powder Actuated Nail 1/4-20 Threaded Rod Right Angle Clip with Powder Actuated Nail installation. Great for overhead Cable Management of CAT5, CAT6 or Fiber Optic Cable. Mount the angle clip and add your threaded rod and j-hook attachments for a simple and easy solution to your cable routing problems. Powder Actuated Nail allows attachment of threaded rod and j-hooks into concrete with this Threaded Rod 90° Angle Clip. ...

Eye Lag Driver, 1/4" Hex - Universal This handy eye-lag screw drill adapter is used to drive eye lag screws with a power-drill. The Eye Lag Driver has a universal 1/4" Hex that fits inside any drill's chuck to mount hanging hardware into ceilings to install j-hooks, threaded rods, etc. for overhead routing and management of CAT5, CAT6 or Fiber Optic cable.

1/2" Hammer-On Beam Flange Clip with 1/4" Hole Attach j-hooks and other hanging hardware from beams that have 5/16-1/2" flanges. This Hammer-On Beam Clip provides a 'portable' 1/4" Hole for overhead routing and management of CAT5, CAT6 or Fiber Optic cable.

1/4" Hammer-On Beam Flange Clip with 1/4" Hole Attach j-hooks and other hanging hardware from beams that have 1/8-1/4" flanges. This Hammer-On Beam Clip provides a 'portable' 1/4" Hole for overhead routing and management of CAT5, CAT6 or Fiber Optic cable.

Magnetic Bridle Rings The Magnetic Bridle Ring is the ideal cable management solution for low voltage wire and cable. Clean, safe, and efficient, the magnetic bridle ring installs from the safety of the ground utilizing an Xtender Pole. No drilling is required for installation. The 3/4" size magnetic bridle rings have a 10-24 machine thread. The 1 1/4" and 2" diameter loop sizes have a 1/4-20 machine thread. Suspend from: Steel Beams Purlins Ceiling Decks Drop Ceiling Channels Metal Joists...

Multi Function Clip, Bat Wing The Multi-Function Clip-Bat Wing allows you to hang ceiling wire and jack chains with ease. It features high-quality all-steel construction, and can be powder-actuated with Bluepoint pin for fastening to concrete. Works with bridle rings, eye lag screws, and beam clamps.

Pressed Beam Clamp Zinc-plated steel Pressed Beam Clamp for flanges up to 1/2" or 3/4" thick such as I-beams. Secure the Pressed Beam Clamp to a beam flange with the included bolt. The Pressed Beam Clamp is ideal for hanging ceiling wires. High quality all steel construction. Has both threaded and non-threaded holes to accommodate jack chain, ceiling wire, or threaded rod.

Steel Bridle Rings for Beam Clamps, 10x24 Thread Support and secure your communication and other low voltage cables with this 3/4" or 2" diameter bridle ring. Simple, effective and constructed of solid, low carbon steel. Excellent for use with our Beam Clamps to help manage cables. The perfect choice for cable management made easy!

1/4-20 Male Threaded Rod Couplers with 3/4" Sheet Metal Screws - 100 Pack Used for hanging ceiling wire & jack chain, and eye lag screws, this threaded rod coupler installs into sheet metal with the self-tapping screw - no need for a pilot hole. Once installed, add 1/4-20 threaded rod and j-hooks or other hanging hardware to complete your overhead network cable management solution. This hardware is designed for the most efficient, secure and cost effective solution. This is a 1/4-20 Threaded...

3/8-16 Male Threaded Rod Coupler with 2" Wood Screw Used for hanging ceiling wire & jack chain, and eye lag screws, this Threaded Rod Coupler installs easily into wood or similar material. Once installed, add 3/8-16 threaded rod and j-hooks or other hanging hardware to complete your overhead network cable management solution. This hardware is designed for the most efficient, secure and cost effective solution. This is a 3/8-16 Threaded Rod Male Coupler with 2" Wood Screw intended for attaching...

3/8-16 Male Threaded Rod Coupler with 3/4" Sheet Metal Screw Used for hanging ceiling wire & jack chain, and eye lag screws, this threaded rod coupler installs into sheet metal with the self-tapping screw - no need for a pilot hole. Once installed, add 3/8-16 threaded rod and j-hooks or other hanging hardware to complete your overhead network cable management solution. This hardware is designed for the most efficient, secure and cost effective solution. This is a 3/8-16 Threaded Rod Male...

Installation Tool for Vertical & Angled Overhang Clips This Vertical Overhang Installation Tool is designed to install Vertical and Angled overhead clips. Mount the Overhang Installer onto 1/2" conduit of appropriate length and you never have to leave the floor. You can even assemble your hanging hardware assembly on the ground and use this tool to install it all at once.

Cable Hanging Tool for Magnetic Cable Management Hardware The Cable Hanging Tool is used to safely install magnetic cable management solutions like J-Hooks, bridle rings, and cable holder brackets. The tool can be attached to an extension pole to install cable management devices from the safety of the ground. Will fit with 1/4" rods or extension poles.

1 1/4" Bridle Ring for Beam Clamp, 1/4x20 Thread, Low Carbon Steel Support and secure your communication and other low voltage cables with this 1 1/4" diameter bridle ring. Simple, effective and constructed of solid, low carbon steel. Excellent for use with our Beam Clamps to help manage cables. The perfect choice for cable management made easy!

Female Hex Adapter, 1/4" Male Driver for Xtender Pole™ The Female Hex Adapter is designed for use with any 1/4" hex bit male driver. It is designed to work with the 12" or 18" Xtender pole, which is used for installing hanging hardware from a work floor.

Hex Adapter, 3/8" Open End for Xtender Pole™ This 3/8" Open End Hex Adapter is designed for the 12" or 18" Xtender Pole™. It is commonly used to install cable hanging hardware from the safety of the work floor.

Female Hex Adapter, 5/8" Open for Xtender Pole™ The Female Hex Adapter is designed to work with the 12" or 18" Xtender pole, which is used for installing hanging hardware from a work floor.

1/2" NPT Adapter for Xtender Pole™ The 1/2" NPT Adapter is designed to work with the 12" or 18" Xtender pole, which is used for installing hanging hardware from a work floor.

Drill Adapter Replacement for Xtender Pole™ The Drill Adapter Replacement is designed to work with the 12" or 18" Xtender pole, which is used for installing hanging hardware from a work floor.